How To Install Hardwood Flooring In Your Studio

An art studio is where an artist spends most of his or her time. The studio should be comfortable, well lit and decorated in a manner that can inspire you. Being in a cold, white shell of a studio makes for no inspiration and can prevent you to enjoy your artwork. Remodeling your studio can solve this problem in an instant. An example of remodeling your studio is to redo the floors. Installing hard wood floors is a great option and will improve the overall look of your studio, which is the ultimate goal in the end.

Guide To Install These Floors

Installing-Hardwood-Floors-Hardwood-Floor-Installation

For those who want to save on the installation fees that they would pay a contractor, you can use this step-by-step guide to help you.

Step 1

The first step is to select the board widths and the hardwood species, such as beech, maple, oak or walnut. And before you can order the hardwood planks, you will need to measure the area of the room. It is advisable to place an order for hardwood boards with a total area of 110 to 115 percent of your calculated room area. This will provide some allowance for any errors in cutting and any irregular planks. Those who want to save further can look for discount hardwood flooring. And before you can install hardwood flooring, it is vital to check the sub-floor for squeaks and to place vapor barrier paper on the sub-floor.

Step 2

It is important to make sure the sub-floor is at lease three-fourths of an inch and that there are no squeaks. If you do find a squeak, the remedy is to use a drywall screw to join the joist and sub-floor in that area. Next, roll out the vapor barrier paper strips and staple them to the sub-floor. After this, make sure that you have all of the tools required and you can begin to install hardwood flooring. Remember to provide a clearance of three-eighths inch from the baseboard so that there is room for expansion when the air is hot and humid.

Step 3

When installing wood floors, start by choosing a long plank for the first row. Make sure that you will be laying the first planks perpendicular to the joists below. After the installation of the first few rows, you will have to drill pilot holes through the tongue of each board. You should hand nail the rolls until there is sufficient space for the nail gun. You will then use the nail gun to staple the tongue of the hardwood board. After the last board has been installed, if there is a narrow gap, measure it and rip the final board to fit it in. Place wood putty on all of the nail holes while making sure the color of the putty is compatible with the floor.

Step 4

After the installation of the hardwood planks, it is time for sanding hardwood floors. You may need to utilize a window fan to eliminate most of the dust that the sander is unable to get into the dust bags. Remember to use an edge sander to take care of the portion that is close to the wall. Make sure that the sanding direction is consistent. A vital guideline to follow when you want to install hardwood flooring is to ensure that when you are blind-nailing not to use a hammer to drive the nails until it is flush with the floor. Instead, the head of the nail must be left projecting by about 1/8 inch. You will then place a nail set sideways over the the top of the nail and then tap the nail set with the hammer to drive the nail.

Tips On Cleaning Hardwood Floors

This article presents tips on cleaning hardwood floors. Caring for floors made from wood is easy and with the proper care and maintenance, you may continue to enjoy its natural beauty. First of all, it is advisable to clean water spills right away because water is one of the worst enemies of wood floors. And whether you are cleaning solid hardwood or engineered hardwood flooring the strategies are basically the same because the thin top layer of engineered flooring is made from real hardwood. The basic tool for cleaning hardwood floors is a terrycloth mop that is equipped with rotating head.

Removing Tough Stains And Spills

hardwood_entryWhen removing tough spills and stains, it is advisable to spray a cleaning product that is specially formulated for wood floors. However, you may also use a mixture of white vinegar and warm water. The correct proportion is a gallon of water to a half cup of white vinegar. You can apply the solution using a mop while focusing on those areas that seem to be dirty. However, avoid soaking the floor with water by putting too much on the mop. You may also need to dry the area with a dry towel or mop.

Time For Sanding

However, if there is too much wear, cleaning hardwood floors may no longer be sufficient. Sanding hardwood floors may be necessary. Refinishing hardwood floor will be the next step after sanding to ensure that the luster and shine will return. However, sanding and refinishing should only be done if screening and recoating with urethane are not able to return the hardwood floor to its former glory. If the damage is confined to a small area, it may be advisable to simply replace the planks in that area instead of repairing the whole area.

Preventing Allergies

Meanwhile, if some members of your household have allergies, it is important to know how to steam clean hardwood floors to remove allergens. A portable steam cleaner that is specifically designed for hardwood floors is recommended. This will deodorize and sanitize the surfaces without the use of detergents and other chemicals that may cause allergic reactions. The steam cleaner will be able to kill dust mites, remove grease, mold, mildew and dirt. You may also use this steam cleaner on beddings, bathrooms, fabrics, carpets, mirrors, linoleum, windows, ovens, grills, and tiles. However, before you start steam cleaning, you should take care to sweep away dust and grit. And if there are worn spots on the floor where the seal has been broken, using the steam cleaner on these spots is not recommended.

After cleaning hardwood floors it is also important to protect the finish of the floors to minimize damage to the surfaces. Exposure to sunlight should be avoided as this could cause the wood to darken or fade. You can rotate area rugs to ensure equal exposure of the various areas. It is also prudent to trim the nails of your pets and to avoid using stiletto heels as these could cause dents on the floor surface. Also, protectors can be used on the legs of tables and other furniture to prevent them from scratching the floor.